A press brake can generate substantial forming force, but the tooling determines how that force shapes the sheet. The punch contacts the upper surface while the press brake die supports and forms the material from below. Their geometry, alignment, hardness, and compatibility influence the bend angle, inside radius, surface condition, repeatability, and amount of setup time required for each job.
What Is the Bending Process?
Bending is a metalworking process that plastically deforms sheet or plate into a required angle or profile. The workpiece is positioned between an upper punch and lower die, and the press brake ram moves the punch toward the die. Once the applied force exceeds the material’s elastic limit, the sheet retains a permanent bend after the load is released.
Manufacturers use bending to make brackets, cabinets, frames, channels, enclosures, appliance panels, vehicle parts, and precision components. It can produce V shapes, U shapes, offsets, hems, radiused profiles, and multi-bend parts without joining separate pieces. CNC control, accurate backgauging, and suitable tooling make the process repeatable across both prototypes and production batches.
The tooling must suit the material and geometry. A narrow opening can produce a tighter inside radius but requires more forming force. A larger opening reduces tonnage but increases the natural radius and minimum flange length. Surface-sensitive stainless steel, aluminum, or coated sheet may also require mark-reducing tooling or protective inserts.
What Is a Press Brake Die?
A press brake die is the lower forming tool installed on the press brake table or die holder. It works with an upper punch to support the sheet and define the space into which the material is formed. In a typical V-bending setup, the punch pushes the sheet into a V-shaped opening. The depth of penetration, punch angle, die angle, opening width, and material springback determine the finished bend.
Punch and die selection affects more than the nominal angle. The tooling influences the inside bend radius, flange length, tonnage, straightness, marking risk, and consistency along the part. Worn shoulders, incorrect alignment, or a die opening that is too small can increase force and produce inconsistent results. A correctly matched set helps reduce trial bends, scrap, tool changes, and unplanned downtime.

How Punches and Dies Work Together
The punch forms the upper side of the bend while the die supports the lower side. Neither tool can produce a controlled result alone. The punch profile must clear the workpiece, especially when a part has return flanges or previous bends. The die must provide the correct opening and shoulder geometry while remaining compatible with the holder, clamping system, and machine load.
Air bending is widely used because the sheet contacts the punch tip and the two die shoulders rather than conforming fully to the die. One tool set can therefore make several angles by changing ram depth. Bottom bending uses deeper penetration and greater contact with the die, while coining uses much higher pressure to force the material closely into the tooling geometry.
Why Die Quality Matters
Tool steel quality, machining accuracy, heat treatment, hardness consistency, grinding, and surface treatment all influence service life. Good tooling maintains its profile under repeated loading and helps preserve angle consistency across long parts. Accurate segmentation and reliable clamping are equally important when operators combine several tool sections for boxes or complex workpieces.
FW Tooling supplies standard and custom press brake tooling in several interface systems. Its S1 range is compatible with Amada-style applications, S2 covers Trumpf-style tooling, S3 supports Bystronic-style requirements, S4 addresses LVD-style systems, and SX includes additional American, EHT, Weinbrenner, and Ursviken configurations.
Common Types of Press Brake Dies
V-Dies and Multi-V Dies
The V-die is the most common lower tool. It is available with different opening widths and groove angles for air bending, bottom bending, and acute-angle work. A 2V die carries two grooves, while a multi-V or four-way die block places several openings on different faces. Rotating the block changes the opening without replacing the whole die, which can shorten setup time when a shop processes several thicknesses.
A common starting point for mild-steel air bending is a V-opening near eight times the material thickness. This rule is a practical estimate rather than a universal requirement. Material tensile strength, desired inside radius, flange length, available tonnage, and the machine’s bending chart must still be checked. In air bending, the inside radius is often related to the die opening, so changing the opening also changes the finished geometry.
U-Dies and Channel Dies
U-dies and channel dies form a flat-bottomed channel with two sides. They are used for trays, supports, frames, and enclosure components. The punch width, channel depth, side clearance, springback, and part-removal path must be considered because the workpiece contacts more tooling surfaces than it does in a simple V-bend.
Offset, Hemming and Special Forming Dies
Offset tooling produces two bends in one stroke to create a Z-shaped step. Hemming tools first create an acute bend and then flatten the edge, improving stiffness and removing a sharp exposed edge. Gooseneck punches provide clearance around return flanges. Radius, curling, beading, rib-forming, corrugating, tube-forming, and wiping dies address profiles that standard V-tooling cannot make efficiently.
Mark-Reducing and Rotary Dies
Urethane tooling, nylon inserts, rolling-ball dies, and carefully polished shoulders can reduce scratches on decorative or coated sheet. Rotary dies use a rotating insert to lower friction during forming. These options are useful when surface appearance is a key acceptance requirement, although the selected system must still deliver the required angle and dimensional tolerance.

How to Choose a Press Brake Die
Begin with the drawing and material rather than the tooling catalog. Confirm sheet type, thickness, bend angle, inside radius, flange length, part profile, surface requirement, bend length, and production quantity. Then check the press brake’s clamping style, working height, load limit, crowning system, and available stroke.
Match the tooling interface to the machine and quick-clamping system. Amada, Trumpf, Bystronic, LVD, WILA, European, and American-style systems use different tangs, holders, safety features, and working heights.
Choose the V-opening with the required radius, flange, and tonnage in mind. A small opening is not automatically more accurate if it overloads the machine or marks the part.
Check punch clearance for boxes, return flanges, and previously formed sections. A straight punch may collide where a gooseneck or segmented punch can clear the workpiece.
Specify material and heat treatment for the expected duty cycle. High-frequency or heavy-tonnage work may justify 42CrMo tooling, hardened working areas, laser hardening, or protective coatings.
Decide whether standard tooling can produce the part. Custom R-type, U-type, compound, segmented, or non-standard tooling may reduce operations for unusual profiles.
FW Tooling offers documented examples across angles, radii, V-openings, and working heights, including narrow acute tools, multi-opening dies, wide V-dies, and custom profiles. Buyers can start with Amada-style S1 tooling, Trumpf-style S2 tooling, or the corresponding S3, S4, and SX systems, then provide drawings for a compatibility and forming review.

Source Press Brake Dies From FW Tooling
Maanshan Fangwei Press Brake Tooling Co., Ltd. has manufactured press brake tooling and shearing blades since 2000 in Bowang, Maanshan. Its product range covers standard machine interfaces and custom forming requirements, with options such as chemical treatment, laser hardening, sand blasting, laser marking, and OEM identification.
For a useful quotation, send the press brake brand and model, clamping interface, tooling drawing or target part drawing, material grade, thickness range, bend length, required angle and radius, and production quantity. This information allows the tooling geometry, material, sectional layout, working height, and treatment process to be reviewed before manufacturing.

